Forum for Information only

Dodge50 > Technical section > Technical Specs Go to subcategory:
Author Content
terkaa
  • Rank:Dodge Fan
  • Score:316
  • Posts:74
  • From:Finland
  • Register:04/08/2011 05:28:10

Date Posted:05/08/2011 06:29:10Copy HTML

What is rear axle on MK1 50's ? Is it Rockwell? Also how is joint made between Phaser 110T and TF727 autotrans? Is there an adapter plate between engine clutch housing and trans? Or is there suitable clutch housing already bolted on engine? I would really like to see a pic of Phaser 110T and TF727



Tero
Finland

Karrier Share to: Facebook Twitter MSN linkedin google yahoo #1
  • Rank:Ummmmmmm
  • Score:11828
  • Posts:3686
  • From:England
  • Register:02/10/2003 09:22:56

Re:Rear axle manufacturer?Phaser 110T + TF727 how?

Date Posted:05/08/2011 02:01:59Copy HTML

Hi there, the rear axles are UK dodge / renault axles not fitted to any other vehicle as far as i know, there were 3 different types and lots of ratio's available.
ax6 fitted to 4.600kgs and 5600kgs vehicles
ax8 fitted to 6600kgs vehicles
ax9 fitted to 7500kgs vehicles

TheA727 was the main autobox fitted though later vehicles (mainly 7500kgs buses) were fitted with an alinson autobox.

The a727 is designed to bolt directly onto the flywheel housing though I am not sure of the differences between housing on the manual and auto boxs.


I will try to find some info on the alinson box for you and some pictures too but I will have to do later cos i just done a 250 mile drive.
"Nothing travels faster than the speed of light with the possible exception of bad news, which obeys its own special laws." Douglas Adams
terkaa Share to: Facebook Twitter MSN linkedin google yahoo #2
  • Rank:Dodge Fan
  • Score:316
  • Posts:74
  • From:Finland
  • Register:04/08/2011 05:28:10

Re:Rear axle manufacturer?Phaser 110T + TF727 how?

Date Posted:06/08/2011 11:11:17Copy HTML

Hi,

  Then it has to be TF727 that has SAE3 flange. It has also been used in IH Scouts with Nissan SD33 diesel and also Early Cummins powered dodge RAM pickups.



Tero
Ex_Member Share to: Facebook Twitter MSN linkedin google yahoo #3
  • Rank:
  • Score:0
  • Posts:0
  • From:Unknown
  • Register:21/09/2018 12:36:07

Re:Rear axle manufacturer?Phaser 110T + TF727 how?

Date Posted:08/11/2011 08:01:47Copy HTML

Chrysler Torqueflight a727    used in many Chrysler/Plymouth/Dodge Cars & Trucks in USA   & even Chrysler engined Jensen Interceptor uk GT car of the 1970`s    Should be lots of info on the box .but be surprised if they ever heard of a 50 series though !
DISINFORMATION: This website has been knocked together with 2 bricks and a rubber chicken for your delight and I hope you all enjoy the fine discussions we have on the wonderful dodge50 series of vehicles, all information is either gleened from the official 50 series workshop manuals OR posted by members of the community.

DATINFORMATION: dodge50.co.uk takes no responsibility for any mistakes or advice given, it's up to you if you take it or not, remember, All material is copyright dodge50.co.uk 2002-2018 unless it's someone else's and it has been begged, borrowed or made up.

DISCLAIMER: Any libel or mistakes in messages that are written by members of the community, inc the admin's and owner of this site, dodge50.co.uk takes no responsibility for them, you need to contact the author and have a moan / send a writ / agree. (delete as you see fit) Blah Blah Blah Blah Blah Blah.......Etc.......Etc...........

free counters

Copyright © 2000- Aimoo Free Forum All rights reserved.